Next issue . . .

classic Classic list List threaded Threaded
3 messages Options
Reply | Threaded
Open this post in threaded view
|

Next issue . . .

jrem
All:

I turned off (commented out) rgr_sound_delay and my previous problem went away (no auto tx on squelch close).

Now I would like to know if there is a way to turn off all speech announcements, i.e., startup, connected, hour time announcement, etc.   I don't want to tie up the clubs repeater unless someone is actually using (transmitting) on echolink.

Thanks, 

John KD9BSD

------------------------------------------------------------------------------
Check out the vibrant tech community on one of the world's most
engaging tech sites, SlashDot.org! http://sdm.link/slashdot
_______________________________________________
Svxlink-devel mailing list
[hidden email]
https://lists.sourceforge.net/lists/listinfo/svxlink-devel
Reply | Threaded
Open this post in threaded view
|

Re: Next issue . . .

Matthew Miller
I think I stopped most of that by modifying the svxlink.conf so it doesn't do the long-ID and set short ID to only after TX (forget the exact option, I am not at home but it was in the svxlink manpage)



Sent from my Verizon 4G LTE smartphone


-------- Original message --------
From: jrem <[hidden email]>
Date: 2/24/17 2:38 PM (GMT-05:00)
To: [hidden email]
Subject: [Svxlink-devel] Next issue . . .

All:

I turned off (commented out) rgr_sound_delay and my previous problem went away (no auto tx on squelch close).

Now I would like to know if there is a way to turn off all speech announcements, i.e., startup, connected, hour time announcement, etc.   I don't want to tie up the clubs repeater unless someone is actually using (transmitting) on echolink.

Thanks, 

John KD9BSD

------------------------------------------------------------------------------
Check out the vibrant tech community on one of the world's most
engaging tech sites, SlashDot.org! http://sdm.link/slashdot
_______________________________________________
Svxlink-devel mailing list
[hidden email]
https://lists.sourceforge.net/lists/listinfo/svxlink-devel
Reply | Threaded
Open this post in threaded view
|

Re: Next issue . . .

Gunnar Widell
Comment out these lines or set to 0.
#SHORT_IDENT_INTERVAL=60
#LONG_IDENT_INTERVAL=60

From the man page:

SHORT_IDENT_INTERVAL

The number of minutes between short identifications. The purpose of the short identification is to just announce that the station is on the air. Typically just the callsign is transmitted. For a repeater a good value is ten minutes and for a simplex node one time every 60 minutes is probably enough. The LONG_IDENT_INTERVAL must be an even multiple of the SHORT_IDENT_INTERVAL so if LONG_IDENT_INTERVAL is 60 then the legal values for SHORT_IDENT_INTERVAL are: 1, 2, 3, 4, 5, 6, 10, 12, 15, 20, 30, 60. If unset or set to 0, disable short identifications.

LONG_IDENT_INTERVAL

The number of minutes between long identifications. The purpose of the long identification is to transmit some more information about the station status (new voice mails etc). The time of day is also transmitted. A good value here is 60 minutes. If unset or set to 0, disable long identifications.

IDENT_ONLY_AFTER_TX

This feature controls when identification is done. By default, identification is done every time the SHORT_IDENT_INTERVAL expires. If this feature is enabled, identification will be done only if there has been a recent transmission. This feature is good for nodes using an RF link to provide echolink to a repeater. Often, in this situation, it is not desirable for the link to identify unless legally necessary. Note that SHORT_IDENT_INTERVAL still have to be set for this feature to work. That config variable will then be interpreted as the minimum number of seconds between identifications. The LONG_IDENT_INTERVAL will not be affected by this parameter.



73 de Gunnar SM3SGP


2017-02-24 23:37 GMT+01:00 Matthew Miller <[hidden email]>:
I think I stopped most of that by modifying the svxlink.conf so it doesn't do the long-ID and set short ID to only after TX (forget the exact option, I am not at home but it was in the svxlink manpage)



Sent from my Verizon 4G LTE smartphone


-------- Original message --------
From: jrem <[hidden email]>
Date: 2/24/17 2:38 PM (GMT-05:00)
To: [hidden email]
Subject: [Svxlink-devel] Next issue . . .

All:

I turned off (commented out) rgr_sound_delay and my previous problem went away (no auto tx on squelch close).

Now I would like to know if there is a way to turn off all speech announcements, i.e., startup, connected, hour time announcement, etc.   I don't want to tie up the clubs repeater unless someone is actually using (transmitting) on echolink.

Thanks, 

John KD9BSD

------------------------------------------------------------------------------
Check out the vibrant tech community on one of the world's most
engaging tech sites, SlashDot.org! http://sdm.link/slashdot
_______________________________________________
Svxlink-devel mailing list
[hidden email]
https://lists.sourceforge.net/lists/listinfo/svxlink-devel



------------------------------------------------------------------------------
Check out the vibrant tech community on one of the world's most
engaging tech sites, SlashDot.org! http://sdm.link/slashdot
_______________________________________________
Svxlink-devel mailing list
[hidden email]
https://lists.sourceforge.net/lists/listinfo/svxlink-devel